HT12D DATASHEET IN PDF

HT12D 2 12 Series of Decoders Features. Operating voltage: V~12V Low power and high noise immunity CMOS Built-in oscillator needs only 5% resistor. IC HT12D can be used only with its pair HT12E. These two ICs together form an Encoder and Decoder pair. They are bit. HT12D Datasheet, HT12D Holtek Decoder Datasheet, buy HT12D Decoder IC.

Author: Grokus Kagabei
Country: Moldova, Republic of
Language: English (Spanish)
Genre: Sex
Published (Last): 2 April 2013
Pages: 205
PDF File Size: 14.20 Mb
ePub File Size: 1.95 Mb
ISBN: 741-5-22579-296-3
Downloads: 95490
Price: Free* [*Free Regsitration Required]
Uploader: Kazahn

What is Web Browser. If you want security you can connect any of the 8 pins to 5V to make it ih. HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders.

It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins. Interface SD Card with Arduino. Choosing Battery for Robots.

This high-density System-in-Package SiP integrates controller, power switches, and support components. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built. A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. Arduino based GPS receiver. Valid transmission; active high. It is very important that your Decoder should have the same address of that of the encoder.

The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to Dxtasheet.

  LIBRO ORIENTACION JUVENIL Y PROFESIONAL 1 JANE COLLINS PDF

SPI Module of Arduino. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. To know how a 4-bit data can be encoded and then datasheeg to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is datasjeet here.

This pin will go high when a data is received. These are the 8-bit address bits, which is used to protect your data. It is not mandatory to use it. Submitted by admin on 27 October In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. This series of decoders are mainly used for remote control system daatsheet, like burglar alarm, car door controller, security system etc.

Skip to main content. Virgin Galactic — Commercial Space Flight. HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. This oscillator can be used by connecting these two pins through a 1M Resistor. The input data code is decoded when no error or unmatched codes are fatasheet.

HT12D Datasheet

In simple terms, HT12D converts the serial input into parallel outputs. Supply voltage; 5V 2. So if you are working on a project which has to h1t2d a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you.

Choosing Motor For Robots. The data on 4 bit latch type output pins remain unchanged until new is received.

  LEY 25357 PDF

HT12D Decoder IC

Interface GPS with Arduino. The serial input data is compared with the local addresses three times continuously. TL — Programmable Reference Voltage. It is mainly provided to interface RF and infrared circuits.

We should set the bits in same pattern on Encoder and Decoder IC to pair them. The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded. If any valid data is received they can be obtained from these four pins.

This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin will go high when a data is received. They are paired with 2 12 series of encoders. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. They can also be connected to LED to physically view the received data. This pin powers the IC should use only 5V.

Connected to the Ground of circuit. The IC has a built in oscillator. The Encoded 12 bit output data obtained from HT12E has to be given here. A valid transmission in indicated by a high signal at VT pin. These two ICs together form an Encoder and Decoder pair.

Author: admin