ECE R26 PDF

Regulation No 26 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of vehicles with. ECE R26 Regulation (03 Series, ) “The uniform regulations on vehicle chapter and section numbering betw een this standard and the ECE R ECE UNIFORM PROVISIONS CONCERNING THE APPROVAL OF: VEHICLES WITH REGARD TO THEIR EXTERNAL PROJECTIONS Incorporating.

Author: Mijas Mazuzragore
Country: Cape Verde
Language: English (Spanish)
Genre: Relationship
Published (Last): 23 October 2016
Pages: 407
PDF File Size: 20.5 Mb
ePub File Size: 2.24 Mb
ISBN: 683-7-48676-876-8
Downloads: 67764
Price: Free* [*Free Regsitration Required]
Uploader: Tajora

UN R56 Moped Headlamps. The dimension of a gap or space between elements of a ecs shall be determined by the distance between two planes passing through the points of contact of the sphere and perpendicular to the line joining those points of contact.

Regulations in Force 1. Uniform Provisions Concerning the Approval of: UN R95 Lateral Collision Protection Occupant Protection in Lateral Collisions Uniform Provisions Concerning the Approval of Vehicles with regard to the R62 of the Occupants in the Event of a Lateral Collision This regulation applies to the lateral collision behavior of the structure of the passenger compartment of M1 and N1 categories of vehicles where the “R” point of the lowest seat is not more than mm from ground level when the unladen efe plus kg i.

If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation the symbol prescribed in paragraph 4. Uniform provisions concerning the approval of passenger cars with regard to electronic stability control systems This regulation was established through the extraction of ESC provisions from UN Regulation H.

With regard to the design basic contour, dimensions, inset, material type and quality and so on and service life they fully correspond to vehicle manufacturer’s replacement wheels.

The material used for the wheel fixing components shall be at least equivalent to the vehicle manufacturer’s replacement wheel fixing components. UN R30 Pneumatic Tires. Canada unilaterally accepts headlamps type-approved under UN R The normal frequency of inspections authorized by the Type Approval Authority shall be one per two years.

The same Contracting Party may not assign the same number to another vehicle type.

Dependent upon the particular vehicle the floor line trace may occur at the bumper section extremity or at the body panel below the bumper. UN R Replacement Airbags.

UN R11 Door Latches. Our fast and r266 means of purchasing up-to-date global vehicle and component standards and regulations on a pay-as-you-go basis. Technical service conducting approval test: Because the design of wheel centre members may vary, test a sufficient number of locations on the wheel rim circumference to ensure that the integrity of the centre members is assessed.

  BREADMAN BK1060S MANUAL PDF

The inspector may take samples at random to be tested in the manufacturer’s laboratory. As from 24 months after the date of entry into force of the 02 series of amendments, Contracting Parties applying this Regulation shall grant ECE approval only if the vehicle type to be fce complies with the requirements of this Regulation fce amended by the 02 series of amendments.

Conformity of production 9. These projections shall in any case satisfy the provisions of r62 5. The Contracting Parties to the Agreement applying the regulation shall communicate to the United Nations secretariat the names and addresses of the Technical Services responsible for conducting approval tests and of the administrative departments which grant approval and to which forms certifying approval or extension or refusal or withdrawal of approval, or production definitely discontinued issued in other countries, are to be sent.

Certificates and licenses

Convertible vehicles shall be examined with the hood in both the raised and lowered positions. UN R36 Bus Construction.

Production definitely discontinued Evaluation Ecd measures which ecd affect the corrosion are to be evaluated covers, crews, zinc or cadmium buses, alloy insulating covers, etc.

In the case where the wheel calliper is outside of the vehicle manufacturer’s replacement wheel calliper, no verification is necessary. Date of report issued by that service: Tyre pressure at start of test nor checked or controlled during the test. Model B See Paragraph 4. UN R Frontal Impact ORS Restraint System in Frontal Impact Uniform provisions concerning the approval of passenger cars in the event of a eve collision with focus on the restraint system This regulation provides for a full-width rigid barrier frontal impact test to evaluate the performance of occupant restraint systems.

Individual measures which may affect the corrosion are to be evaluated covers, crews, zinc or cadmium buses, alloy insulating covers, etc. Consequently, products approved under the above rules do not require subsequent reapproval under UNECE R90 for use in vehicle r6. Luggage racks, ski racks and radio receiving or transmitting aerials that have been approved as separate technical units may not be offered for sale, sold or purchased unless accompanied by assembly instructions.

  KHAT THULUTH PDF

This rule has been superseded by UN Regulation 84 and is noted solely for reference.

Licenses and Certificates

The provisions of Paragraph 5. UN R53 Motorcycle Lighting. In the case where the calliper is inside the vehicle manufacturer’s replacement wheel calliper, a check shall be carried out of wheel operating clearance with respect to brake, suspension and steering components and general under body components, taking into account the effect of wheel balance weights.

Acceptance criteria The test shall be considered satisfactory if there is not any visible fracture penetrating through the wheel surface and if there is not any loss of inflation pressure within one minute of completing the test.

UN R3 Retro-reflecting Devices. UN R Vehicle Recyclability. The basic number of wheel fixings, for example 4 holes, 5 holes and so on, shall not be changed. Ensure that the wheel is mounted on the hub fixture with dimensionally representative fixings such as would be used on a vehicle.

Cee criterion is the brake temperature. The marking of approval rr26, the Regulation number and approval number may be at a distance from each other respecting the sequence.

EUR-Lex Access to European Union law

Uniform Provisions Concerning the Approval of Filament Lamps for Use in Approved Lamp Units of Power-driven Vehicles and of their Trailers UNECE R37 specifies technical and administrative requirements for the approval of a wide range of filament lamps shown in Annex 1 of the regulation that are intended for use in approved lamp units of power-driven vehicles and of their trailers.

The wheel manufacturer’s facilities may be used for test purposes provided that the Type Approval Authority or a designated representative witnesses the tests. The requirement of Paragraph 6. The regulations considers the installation and functioning of lighting equipment as a whole to ensure compatible performance across all types of equipment and devices headlamps, signalling lamps, markers lamps, etc.

InterRegs: Regulation No. | ECE – United Nations

An approved wheel shall not reduce the brake efficiency in comparison with a manufacturer’s replacement wheel. The regulatory text see the GAR pipeline has been adopted and is undergoing the r2 waiting period before its finalization in June This regulation was superseded by UN R Use new wheels each time. EU case law Case law Digital reports Directory of case law.

Author: admin