BUDERUS JUNO 11.1 PDF

Manuals for buderus juno c to download for viewing them online or printout as PDF. Manuals for Buderus Juno 11 download to download for viewing them online or printout as PDF. Buderus Manuals for Support Juno /SF Buderus | GB | Operating instructions | Buderus GB Operating instructions . .. 46 Shut down the heating system using the control unit.

Author: Kajidal Mazshura
Country: Mauritania
Language: English (Spanish)
Genre: Finance
Published (Last): 8 November 2013
Pages: 366
PDF File Size: 13.41 Mb
ePub File Size: 7.34 Mb
ISBN: 614-1-66281-830-4
Downloads: 36788
Price: Free* [*Free Regsitration Required]
Uploader: Zolodal

In the “Midday program” for heating circuit 2, you want to delete the Monday heating phase from The heating system has been factory-set to a pump postpurge period of 5 minutes.

Using pumps, this hot water is transported through the pipework to the consumers radiators, underfloor heating juo, etc. Since the burner has been specifically matched to the particular boiler, the information in the Boiler manual takes precedence.

Download – Buderus

As the base load, only the first stage will be enabled for single and two-stage burners. This creates a risk of scalding at the draw-off points. Approximately 2 seconds later the designation of the currently selected standard program will appear. DO NOT use abrasive cleaning materials. All other modules are explained in separate technical module documentation. If the Boiler is to stand on a floor made of combustible material then protection between the Boiler and the floor should be provided by means of non combustible material.

Buderus GB Operating instructions |

Alternatively remove the switch completely, but the vacated hole must be blanked off. The boiler is operated with the heating system temperature set on the right knob serving as the target value.

  JAVA DOCFLAVOR PDF

Additional programming options New switch. If the temperature is set incorrectly, the underfloor heating system could overheat. Carry out a gas tightness test 30 3.

Typengeprüfte Gebläsebrenner, Heizkessel und Wassererwärmer |

L The control functions remain operational in manual mode. Using the four holes on the external wall plate as a guide drill four fixing holes into the external wall to suit those supplied. The mixers stay at zero volts and should be manually adjusted. All combination Boilers suffer performance budefus due to the effects of hard water limescale build up on heat exchanger surfaces. If the air shutter is adjusted, re-check the Smoke No.

Budersu burner servomotor cannot be reversed. Set the thermostat or other operating control to lowest setting. Heating only recommences if the heating system is subject to a risk of frost.

Screw fill connection and independent vent. A “6A” code can be seen in the display. Slowly open the valve, note is the flow unrestricted, restricted or blocked?

Follow the gas supplier’s instruction. When the Holiday Period is over the Programmer reverts back to the normal programme. The Company takes every reasonable care to ensure that these products are designed and constructed to meet these general safety requirements, when properly used and installed. Check for leaks particularly on older system budedus may have operated on a lower pressure.

Wait 45 seconds before attempting to restart the burner. Family program Family program Monday at Are the Boiler Thermostats set budrrus the desired temperatures? Boilers are dispatched with the Bypass Screw in a labeled envelope attached to the Burner. The Fill and Vent should be suitably capped to prevent ingress of water or fitted with return bends. Move the boiler away from the wall and using a diamond tipped core drill, drill a 6 mm hole in the wall ensuring the hole is level.

  HARDCOURT CONFIDENTIAL PDF

When using the MEC2 programming unit, the reception of the radio clock signal depends on location and position. With the MEC2 programming unit you don’t need to adjust the thermostatic radiator valves before bedtime or in the morning. Heating circuit curve example x Outside temperature y Flow temperature 7 2 What you should know about your heating system Weather-compensated control With weather-compensated control, only the outside temperature captured ubderus the outside temperature sensor buderu decisive for the flow temperature level.

To enable the Huderus, restart the boiler. The display shows “Constant winter”. LED indication We reserve the right to make any changes due to technical modifications!

Typengeprüfte Gebläsebrenner, Heizkessel und Wassererwärmer

Thermostatically controlled showers are recommended for greater comfort and prevention of high temperatures. It is not essential for the boiler to be positioned this way.

If a one pipe gravity feed is employed it must be purged through the vent port.

A Non-Return Valve is not required in the return line. The display shows “Constant day”.

Monday — Friday, from

Author: admin